- Jones State Forest BMP Demonstration Area
- Are You a Tree Farmer?
- Improving My Land Forest Roads and BMPs
- Where Can I Find?
- Repairing Storm Damaged Streamside Management Zones
- Forestry Acronyms
Friday, September 1, 2006
BMP Informer - September 2006
September BMP Q&A
By: Shane Harrington, BMP Forester (Ret.), Texas Forest
Service
Q: I live in
Southeast Texas and much of my timberland was
damaged by Hurricane Rita last fall. My
streamside management zones were damaged as well and I am trying to restore
these areas in order to continue protecting water quality. Would it be better to allow these areas to
naturally heal themselves or should I take action in restoring these areas
myself?
A: That is a
really good question. I am sure that a
lot of people in your area have the same question. Streamside management zones (SMZs) are important in
protecting water quality and providing excellent wildlife habitat. The purpose of an SMZ is to reduce the
potential quantity of sediment and logging debris reaching the stream and to
prevent increased water temperatures.
Caution should be taken when conducting any forest management activity
within the area immediately adjacent to stream channels to ensure the
protection of both instream and downstream water quality. Under proper management, timber production,
wildlife enhancement and water quality may all be achieved.
An initial assessment should be made of any damaged SMZ to determine the
severity, current stocking level, and ability to regenerate. The best option for restoring the SMZ may be
to allow it to naturally regenerate if there are adequate sources for
regeneration of desirable species. Damage
to the SMZ may be severe enough that natural regeneration is not an option and
the area must be artificially regenerated.
Preferred species for planting are Water Oak, Willow Oak, Cherrybark
Oak, Swamp Chestnut Oak, Nutall Oak, Green Ash, Sweetgum, Cottonwood,
and Loblolly Pine. These seedlings
should be hand planted. Intensive site
preparation and machine planting should be avoided in these areas in order to
minimize the potential for sediment and debris from entering the stream.
The SMZ should encompass 50 feet on both sides of all perennial and
intermittent streams and carry a minimum basal area of 50 square feet per acre.
When replanting, every effort should be
made to ensure that the number of seedlings planted will meet the minimum basal
area of 50 square feet in ten years.
Herbaceous weed control may be needed to control competing vegetation and
to increase seedling survival. The
application of herbicides within the SMZ should be done through spot treatment
or individual stem injection. Aerial or
ground broadcast of herbicides should be avoided within the SMZ to prevent any
chemicals form entering the stream. If
the area where the herbicides are to be applied is prone to flooding extra
caution should be taken when applying the treatment or the treatment should be
avoided. Always follow all manufacturing
labels on containers when applying herbicides and always dispose of empty
bottles and trash appropriately.
Whether the SMZ is naturally or artificially regenerated, Texas Best
Management Practices (BMPs) Guidelines should be followed. These guidelines are designed to protect
water quality during any forest management activity. For a copy of the BMP handbook visit your
local Texas Forest Service office or view online at http://txforestservice.tamu.edu/water. For questions regarding repairing damaged
SMZs or BMPs in general please contact me by calling (936) 639-8180.
* This article was published in the September 2006 issue of the Texas Logger
Tuesday, August 1, 2006
BMP Trivia Question
Basal area is a measure of forest density that accounts for the size of the trees. The higher the basal area in a forest, the higher the density of tree cover. Basal area is important to Best Management Practices because Streamside Management Zones (SMZs) need to have at least a minimum basal area of 50 square feet evenly distributed across their area to properly protect perennial and intermittent streams. In order to determine the basal area of a stand you first need to know the basal area formula. Do you know what it is? (Hint look in the “How to Calculate Basal Area” section of the BMP handbook)Click on "comments" below and post your answers.
Saturday, July 1, 2006
July BMP Q&A
By: Shane Harrington, BMP Forester (Ret.), Texas Forest
Service
Q: In recent months the outbreak of
wildfires and the threat of wildfires occurring has been high. I want to protect my timber from a possible
wildfire by installing firelanes around my tract. Are there any BMPs that I should follow
during this project to prevent any impacts on water quality from occurring?
A: Installing firelanes around your timber
is a great way to protect your investment by reducing the threat of a possible
wildfire. Firelanes work by creating a
barrier and removing the available fuel source between adjoining stands or
tracts. By removing the fuel source
along these barriers aids in preventing a wildfire one stand or tract to another. However, it is important to remember that
there are potential impacts to water quality that can occur if caution is not
taken.
Guidelines for properly constructing and maintaining
firelanes can be found in the Texas Forest Service’s BMP Bluebook. These recommendations are designed to prevent
any unnecessary erosion form occurring thus minimizing the potential for
impacts on water quality.
Firelanes should be
constructed along the perimeter of the tract and follow the boundaries of
Streamside Management Zones. Locating these
barriers outside of SMZs will limit the amount of sedimentation that may
result. This will also protect the
litter and organic matter of the SMZ so it can continue to serve as a
filter.
To allow for proper
drainage and erosion control, waterbars and wing ditches should be installed in
a timely manner. Recommendations for
installing these devices can be found on pages 34 and 38 of the BMP
Bluebook. These recommendations include
how to properly build waterbars, proper spacing for waterbars, and specifications
on properly installing wing ditches. When
installing wing ditches, make sure that the runoff water is not being
discharged directly into streams.
Regular maintenance on
firelanes is necessary to avoid potential erosion problems. This includes periodic inspections,
especially after heavy rains, to make sure that they are still functioning
properly and are not washed out. Mowing,
rather than blading, is the preferred type of maintenance because it minimizes the
amount of exposed mineral soil. Care
should be taken when blading is the only option.
Implementing these
control structures can be very costly when using heavy machinery. For economical as well as environmental
reasons, it is important to only build firelanes as wide and deep as necessary. Woody debris and other flammable material
should be kept away from firelanes.
These objects can ignite, creating a pathway for the fire to spread into
SMZs or adjoining lands. If you have a
question regarding BMPs, please call me at (936) 639-8180.
* This article was published in the July 2006 issue of the Texas Logger
Thursday, June 1, 2006
BMP Informer - June 2006
Monday, May 1, 2006
BMP Trivia Question
May BMP Q&A
By: Shane Harrington,
BMP Forester (Ret.), Texas
Forest Service
Q: I would like to know if there is any place that I can
visit in person to see “on the ground” applications of BMPs? I hear the term BMPs used a lot these days
but I am interested in actually seeing how they are used.
A: That is a really good question. Many people hear the term BMPs and may have
an idea of what they are but have never really seen them applied or applied
correctly.
Crushed
concrete was used to stabilize this road providing access during wet months.
The Texas Forest Service established BMP demonstration areas
during the mid 1990’s on the W. Goodrich Jones State Forest located in Conroe and the Kirby
State Forest
located between Kountze and Woodville. The purpose of these BMP demonstration
areas was to give loggers, landowners, and general public a chance to see
properly implemented BMPs. Original
demonstrations included a streamside management zone (SMZ), various types of
stream crossings, and water control structures (i.e. wing ditches, open top box
culverts, etc.).
During 2005 the Texas Forest Service decided to remodel and
update the BMP demonstration area on the Jones
State Forest
in Conroe. Many of the original BMPs that were installed
in the 90’s had deteriorated and were no longer visible. Many of the original BMP demonstrations were renovated
and new BMP demonstrations were added.
Renovation work consisted of remarking the SMZ, clearing brush away from
culvert crossings making the culverts visible again, and replacing the existing
signs with new ones which explain what BMP is being used and its purpose.
A highway entrance using large rocks and timber mats was
added showing how mud can be removed from tires before entering the
highway. Tracking mud onto the highway
can cause the roadway to become slick making it hazardous for other
motorists. Also a flat rail car was
placed across a stream demonstrating how it can be used as a bridge. Sometimes a stream is too large for a culvert
or other type of crossing and a bridge must be used and while there are several
options a flat rail car can provide a sturdy and safe crossing
alternative. Another new demonstration
is road stabilization using crushed concrete which will allow a road to be used
during wetter months. Also grass was
planted along other roadways showing how seeding roads can prevent or minimize
any erosion that may occur.
The guidelines and recommendations for using BMPs can be
found in the Texas Forestry Best Management Practices Handbook. You can get a copy of the handbook by
contacting your local Texas Forest Service office or view it online at http://txforestservice.tamu.edu/water. For more information regarding the BMP
demonstration area or BMPs in general please call me at (936) 639-8180
* This article was published in the May 2006 issue of the Texas Logger
Subscribe to:
Posts (Atom)

